Automatic faucet ZY-8700 CE certificate

Automatic faucet solenoid valve 1.Integrated automatic faucet(including cold&warm water) 2.With temperature adjusting handle

Automatic faucet solenoid valve

Item number: ZY-8700D

1.Control:With its micro-computer controlling . Stop water automatically when water flowing exceed1 minute.

2.Adjustable distance: Induce distance can be adjusted free of touching.

3..Strainer device: Strainer can be removed and cleaned to prevent blocking.

4.Anti-blocking system: The solenoid valve is protected by anti-blocking system.

Technical Data

Model	ZY-8700A	ZY-8700D
Applicable power supply	AC220V/50Hz	DC6V(four 1.5V "AA" size alkaline batteries)
Applicable water pressure	0.05Mpa-0.8Mpa	0.05Mpa-0.8Mpa
Applicable water temperature	0-60	0-60
Environment temerature	0.1-45	0.1-45
Water supplying caliber	1/2"	1/2"

Overall dimensiions

Installation diagram

Instructions for use

Sensor/flow test.

When the unit is powered on, water should flow immediately when you put your hands within range of the sensor. When you remove your hands out range the water should stop immediately.

The maximum duration of continuous flow is 1 minute.

 

      2.     Sensor range

The default factory set distance is 12~15 cm. When powered on  for the first time, place your hands at the desired distance within 5 seconds after the power has been switched on and remove your hands after approx 2 seconds in order to change the factory setting.

To reset the setting, interrupt power for at least 30 seconds and follow the procedure as described to set the sensor range correctly.

 

      3.    Strainer

To prevent blockage please clean the strainer regularly, make sure you shut of the water mains, unscrew the water inlet hose, remove the strainer, clean with water and a soft brush.  Then install the items in reverse order, turn on water mains and check for leakage.

 

 Battery Change:

The indicator light in the sensor will flicker 3 times per second to indicate the batteries are at the end of their useful life. At this stage the unit will not operate in battery more  anymore

In case you have plugged in the mains, disconnect power and open the  cover of the control box, open the battery holder, remove the batteries and replace all batteries with new ones.

Please make sure you install the batteries in the right direction, the + and – side are indicated in the battery holder.

Close the battery holder, place the cover back in place and tighten the screws.

Follow the instructions for setting the sensor range if required.

 

 Problem:

The unit does not work.  Please check for power connection or replace the batteries, check connection of the sensor cable.

There is power however no water flow,

Please check the water supply, open any closed valves if necessary

Check water connections for blockage, clean if necessary

Check Strainer for Blockage, clean if necessary

Disconnect power for 30 seconds and re install

Check water connections for twists

Check sensor cable connection

Clean the sensor with a soft cloth

Caution:

Please handle the product with care whilst installing

Only clean with soft cloth, no abrasive cleaning agent, acidulous cleaning agents.

Do not spray the control with water.

Only clean the sensor with a soft cloth, scratching will reduce the range and sensitivity of the unit itself

Packing:

( function(){ var aBigImageSrc = [ 'http://i01.i.aliimg.com/photo/v10/277021419_1/Automatic_faucet_ZY_8700_CE_certificate.jpg' , 'http://i01.i.aliimg.com/photo/v10/277021419_2/Automatic_faucet_ZY_8700_CE_certificate.jpg' , 'http://i01.i.aliimg.com/photo/v10/277021419_3/Automatic_faucet_ZY_8700_CE_certificate.jpg' , 'http://i01.i.aliimg.com/photo/v10/277021419_4/Automatic_faucet_ZY_8700_CE_certificate.jpg' ]; var oProductShow = new AE.run.minisite.productShow(); oProductShow.init( { 'aImgSrc': aBigImageSrc } ); } )(); Automatic faucet ZY-8700 CE certificate